ild205t, ILD206T, ild207t, ild211t, ild213t www.vishay.com vishay semiconductors rev. 2.1, 23-oct-15 1 document number: 83647 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 optocoupler, phototransistor output, dual channel, soic-8 package description the ild205t, ILD206T, ild207 t, ild211t, and ild213t are optically coupled pairs with a gallium arsenide infrared led and a silicon npn phototrans istor. signal information, including a dc level, can be transmitted by the device while maintaining a high degree of electrical isolation between input and output. the ild205t, ILD206T, ild207t, ild211t, and ild213t come in a standard soic-8 small outline package for surface mounting which makes it ideally suited for high density applications wi th limited space. in addition to eliminating through-holes requirements, this package conforms to standards for surface mounted devices. a specified minimum and ma ximum ctr allows a narrow tolerance in the electrical design of the adjacent circuits. the high bv ceo of 70 v gives a higher safety margin compared to the industry standard of 30 v. features ? two channel coupler ? soic-8 surface mountable package ? standard lead spacing of 0.05" ? available only on tape and reel option (conforms to eia standard 481-2) ? isolation test voltage, 4000 v rms ? compatible with dual wave, vapor phase and ir reflow soldering ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 agency approvals ? ul1577, file no. e5 2744 system code y ? cul - file no. e52744, equivalent to csa bulletin 5a ? ? ? ? ? ? ? i179018-2 a1 c2 a3 c4 8c 7e 6c 5e i179025 ordering information ild2##t part number agency certified/package ctr (%) 10 ma ul, cul 40 to 80 63 to 125 100 to 200 ? 20 ? 100 soic-8 ild205t ILD206T ild207t ild211t ild213t s ioc-8 6.1 mm
ild205t, ILD206T, ild207t, ild211t, ild213t www.vishay.com vishay semiconductors rev. 2.1, 23-oct-15 2 document number: 83647 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the absolu te maximum ratings can ca use permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of th e time can adversely affect reliability. (1) refer to reflow profile for soldering conditions for surface mounted devices. note ? minimum and maximum values were tested requierements. typical values are characteristics of the device and are the result of e ngineering evaluations. typical values are for information only and are not part of the testing requirements. absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input peak reverse voltage v r 6v peak pulsed current 1 s, 300 pps 1 a continuous forward current per channel i f 30 ma power di ssipation p diss 50 mw output collector emitter breakdown voltage bv ceo 70 v emitter collector breakdown voltage bv eco 7v power dissipa tion per channel p diss 125 mw coupler total package dissipation ambient ? (2 leds and 2 detectors, 2 channels) p tot 350 mw storage temperature t stg -55 to +150 c operating temperature t amb -55 to +100 c soldering time from 260 c (1) t sld 10 s electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit input forward voltage i f = 10 ma v f -1.21.55v reverse current v r = 6 v i r - 0.1 100 a capacitance v r = 0 v c o -25-pf output collector emitter breakdown voltage i c = 10 a bv ceo 70 - - v emitter collector breakdown voltage i e = 10 a bv eco 7--v collector emitter leakage current v ce = 10 v, i f = 0 a i ceo - 5 50 na collector emitte r capacitance v ce = 0 v c ce -10-pf coupler collector emitter sa turation voltage i f = 10 ma, i c = 2.5 ma v cesat --0.4v capacitance (input to output) c io -0.5- pf current transfer ratio (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit i c /i f v ce = 5 v, i f = 10 ma ild205t ctr dc 40 - 80 % ILD206T ctr dc 63 - 125 % ild207t ctr dc 100 - 200 % ild211t ctr dc 20 - - % ild213t ctr dc 100 - - % v ce = 5 v, i f = 1 ma ild205t ctr dc 13 30 - % ILD206T ctr dc 22 45 - % ild207t ctr dc 34 70 - %
ild205t, ILD206T, ild207t, ild211t, ild213t www.vishay.com vishay semiconductors rev. 2.1, 23-oct-15 3 document number: 83647 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 1 - test circuit, non-saturated operation fig. 2 - test circuit, saturated operation fig. 3 - switching times switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit delay time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 1) t d -3-s rise time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 1) t r -3-s fall time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 1) t f -4.7- s storage time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 1) t s -0.3- s turn-on time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 1) t on -6-s turn-off time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 1) t off -5-s turn-on time v s = 5 v, i f = 10 ma, r l = 1 k ? , (see figure 2) t on -3-s turn-off time v s = 5 v, i f = 10 ma, r l = 1 k ? , (see figure 2) t off -10-s channel i channel ii 95 10804 r g = 50 t p t p = 50 s t = 0.01 + 5 v i f 0 50 100 i f i c = 2 ma; adjusted through input amplitude oscilloscope r l = 1 m c l = 20 pf channel i channel ii 95 10843 r g = 50 t p t p = 50 s t = 0.01 + 5 v i c i f 0 50 1 k i f = 10 ma oscilloscope r l c l 20 pf 1 m t p t t 0 0 10 % 90 % 100 % t r t d t on t s t f t off i f i c t p pulse duration t d delay time t r rise time t on (= t d + t r ) turn-on time t s storage time t f fall time t off (= t s + t f ) turn-off time 96 11698
ild205t, ILD206T, ild207t, ild211t, ild213t www.vishay.com vishay semiconductors rev. 2.1, 23-oct-15 4 document number: 83647 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? as per iec 60747-5-5, 7.4.3.8.2, this opto coupler is suitable for saf e electrical insulation only within the safety rating s. compliance with the safety ratings shall be ensured by means of protective circuits. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 4 - forward voltage vs. forward current fig. 5 - collector current vs . collector emitter voltage (non-saturated) fig. 6 - leakage current vs. ambient temperature fig. 7 - collector current vs. collector emitter voltage (saturated) safety and insulation ratings parameter test condition symbol value unit climatic classifica tion according to iec 68 part 1 55/100/21 comparative tracking index cti 175 tested withstanding isolation vo ltage according to ul1577, t = 1 s v iso 4000 v rms maximum transient isol ation voltage according to din en 60747-5-5 v iotm 6000 v peak maximum repetitive peak isolation voltage acc ording to din en 60747-5-5 v iorm 560 v peak isolation resistance t amb = 25 c, v io = 500 v r io ? 10 12 ? t amb = 100 c, v io = 500 v r io ? 10 11 ? output safety power p so 350 mw input safety current i si 150 ma input safety temperature t s 165 c creepage distance dip-6, option 6 4 mm clearance distance dip-6, option 6 4 mm insulation thickness 0.2 mm 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 0.1 1 10 100 v f - forward voltage (v) i f - forward current (ma) t amb = 0 c t amb = 25 c t amb = 50 c t amb = 75 c t amb = 100 c t amb = -55 c 22327 0 5 10 15 20 25 0246810 i c - collector current (ma) v ce - collector emitter voltage (n s ) (v) i f = 30 ma i f = 20 ma i f = 15 ma i f = 10 ma i f = 5 ma 0.001 0.1 10 1000 i ce0 - leakage current (na) t amb - ambient temperature (c) i f = 0 ma v ce = 40 v v ce = 24 v v ce = 12 v -60 -40 -20 0 20 40 60 80 100 22329 0 5 10 15 20 25 30 0 0.1 0.2 0.3 0.4 i c - collector current (ma) v ce - collector emitter voltage ( s at) (v) i f = 25 ma i f = 10 ma i f = 5 ma i f = 2 ma i f = 1 ma
ild205t, ILD206T, ild207t, ild211t, ild213t www.vishay.com vishay semiconductors rev. 2.1, 23-oct-15 5 document number: 83647 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 8 - normalized ctr (saturated) vs. ambient temperature fig. 9 - normalized ctr (non-saturated) vs. ambient temperature fig. 10 - normalized ctr (non-saturated) vs. forward current fig. 11 - normalized ctr (saturated) vs. forward current fig. 12 - switching time vs. load resistance fig. 13 - power dissipation vs. ambient temperature 0 0.2 0.4 0.6 0.8 1.0 1.2 -60 -40 -20 0 20 40 60 80 100 120 n ctr - normalized ctr (non- s at.) t amb - ambient temperature ( c) normalized to ctr value: i f = 10 ma, v ce = 5 v, t amb = 25 c i f = 10 ma i f = 1 ma 0 0.2 0.4 0.6 0.8 1.0 -60 -40 -20 0 20 40 60 80 100 120 n ctr - normalized ctr ( s at.) t amb - ambient temperature ( c) normalized to ctr value: i f = 10 ma, v ce = 5 v, t amb = 25 c i f = 10 ma i f = 1 ma 0 0.2 0.4 0.6 0.8 1.0 1.2 0.1 1 10 100 n ctr - normalized ctr (n s ) i f - forward current (ma) normalized to: i f = 10 ma, v ce = 5 v, t amb = 25 c t amb = 0 c t amb = 100 c t amb = 75 c t amb = -55 c t amb = 25 c 0 0.2 0.4 0.6 0.8 1.0 1.2 0.1 1 10 100 n ctr - normalized ctr ( s at) i f - forward current (ma) v ce = 0.4 v normalized to: i f = 10 ma, v ce = 5 v, t amb = 25 c t amb = 0 c t amb = 75 c t amb = -55 c t amb = 25 c t amb = 100 c 22336 0.1 1 10 100 1000 0 5 10 15 20 t on , t off - s witching time ( s ) r l - load re s i s tance (k ) t on ( s ) t off ( s ) v ce = 5 v, i f = 10 ma 0 50 100 150 200 250 300 350 400 -55 -30 -5 20 45 70 95 120 package power di ss ipation (mw) t amb - ambient temperature (c) dual channel s ingle channel
ild205t, ILD206T, ild207t, ild211t, ild213t www.vishay.com vishay semiconductors rev. 2.1, 23-oct-15 6 document number: 83647 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions (in millimeters) package marking (example) note ? tape and reel suffix (t) is not part of the package marking. d205 v yww y 68
ild205t, ILD206T, ild207t, ild211t, ild213t www.vishay.com vishay semiconductors rev. 2.1, 23-oct-15 7 document number: 83647 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tape and reel packaging for dual channels (1) (in millimeters) selected dual soic8 optocouplers are available in tape and reel format. to order surface mount ild2xx optocoupler on tape and reel, add a suffix t after the part number, i.e., ild207t. the tape is 16 mm and is wound on a 33 cm reel. there are 2000 parts per reel. taped and reeled dual soic8 optocouplers conform to eia-481-2 and iec 60286-3. note (1) select dual channel devices are available in the shorter soic-8 package and will be taped according to the single channel taping specification ? fig. 14 solder profile fig. 15 - lead (pb)-free reflow solder profile according to j-std-020 handling and storage conditions esd level: hbm class 2 floor life: unlimited conditions: t amb < 30 c, rh < 85 % moisture sensitivity level 1, according to j-std-020 1.5 (0.059) 1.75 0.1 (0.069 0.004) 13.3 (0.523) 0.3 (0.012) max. 0.1 (0.004) max. 16.0 0.3 (0.630 0.012) 18004 4 0.1 (1.57 0.004) 2 0.05 (0.079 0.002) 6.6 (0.26) 6.35 (0.25) 8.0 (0.315) 7.5 0.05 (0.300 0.002) 3.8 (0.15) embossment direction of feed center lines of cavity 10 pitch cumulative tolerance on tape 0.2 (0.008) 1.5 (0.059) min. pin 1 and top of component top cover tape 0 50 100 150 200 250 300 0 50 100 150 200 250 300 time (s) temperature (c) 240 c 245 c max. 260 c max. 120 s max. 100 s 217 c max. 30 s max. ramp up 3 c/s max. ramp down 6 c/s 19841 255 c
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
